QC Cover Stud 3/8" -16 x 1 3/4"

Quick Change Yoke Bolt and washer

Grade 9 bolt
Belleville Domed Wash
torque to 45 ft lbs with red loctite

10 piece carrier shim kit

for quick change spools with 2.0" and 3.031" OD jousrnals

Thin side bell o-ring for Winters and PEM 6 rib Bell Quick Changes.

Set of three Back cover gasket, sprint.

Quick Change Rear End Side Bell Carrier Seal

for quick change spools with 2.0" and 3.031" OD journals

Koyo Lower Shaft Front Bearing

6207ZZ sealed bearing

QCC0104 Sprint rear Cover Gasket with HD Steel Core

PEM Quick Change Rear End Thrust Block Assembly

Allen head Screw
Lock Nut
Flat Washer
Thrust Block

Also fits other brands.

QC Snout Nut Alum. wide 5 with locking system

• wide 5 hub seal for PEM Aluminum 1 ton rear end tube.

• Locking Snout Nut Assy for PEM Aluminum 1 ton rear end tube.
• Also fits 1 ton Winters snout tubes
• Does not fit DMI duece and a half

Rear pinion retainer

Koyo Lower Shaft Front Bearing

6307ZZ sealed bearing

Locking Right Hand Thread Nut Kit
for 2.5" Grand National Hub

NEW! PEM Gear Lube 75-140w Full Synthetic 1 quart

Tested in 2023 and 2024 to reduce rear end temperatures
by the 2024 UMP Modified National Champion.

Not for positraction or clutch style traction differentials

• stainless wear sleeve for PEM Aluminum 1 ton rear end tube.

Vent kit for 2022 and up PEM quick change rear ends.
18" hose and a push fit in fitting.

Quick change rear end only shown in picture so you know how to install. (it is not included).

• New Short nuts
• fits PEM, DMI, Winters, Frankland and other quick change rears
  
• Aluminum High Nuts for QC rear end - 6 pieces
• 3/8 inch x 16 thread
  
• These nuts will work with standard size cover studs

Ring gear bolts with belleville washers, 12 of each piece

fits PEM, Winters, DMI and Tiger QC rears

fits 10 spline Quick Change Rear End
Lower shafts

1310 U joint size

• New Short nuts
• fits PEM, DMI, Winters, Frankland and other quick change rears
  
• Aluminum High Nuts for QC rear end - 6 pieces
• 3/8 inch x 16 thread
  
• These nuts will work with standard size cover studs

Quick Change Right Hand Posi Nut for Pinion
fits PEM, Winters, DMI & Tiger quick changes

• Aluminum Locking Nut for Quick Change Rear End Pinion
• Right Hand Thread
• takes a 1 7/8" extra deep socket

Quick Chamge Yoke Installation Kit with bolt, waher and threadlocker
fits 10 spline Quick Change Rear End Lower shafts
1310 U joint size

• Bearing and seal kit for PEM Aluminum 1 ton rear end tube.
• Bearings and Races are REM ISF Microfinished for less resistance
• 2 bearings, 2 races and Seal

GM Metric Suspension Top Mount for Quick Change Rear End

new welded design for 2025

• Fits Quick Change Rear Ends, PEM, Winters, DMI, Tiger and Frankland Rears.
• Fits 6 rib and 8 rib side bells without modification
• 4 degrees down pinion angle built in with stock length radius rods
• Poly top bushings for stock style General Motors radius rods
• Raw Mild Steel, Not painted

Quick Change Lower Shaft - Heat Treated
fits PEM, Winters, DMI & Tiger quick change rears

.188" wall Centerless Ground Steel Tubing, exact 2.99" to 3.00" outside dimension.
2.5" GN snout for standard and lightweight Grand National Hubs.
24" end to end measurement fits both sides of a 60" centered pinion quick change rear.
You can shorten with a standard chop saw or band saw.
pick your size for different wide quick changes and offset quick changes.

Steel Tube with Howe Vogel 2.0" GN Snout 2.999 to 3.000" OD.

• B MEASUREMENT specify length measured from inner bearing step to end of tubing.
• 3" OD centerless ground .188" wall tubing to fit in quick change rear end side bell.
• You can cut this tube easily with a chop saw or band saw for shorter length axles