Home > 9" HOUSING, AXLE & HUB > 9" Ford GN Floater Rear
Sort By:
Page of 4
O-Ring for PEM Dust Cap O-Ring for PEM GN GN Hub Thick O-Ring for Grand National Hub
O-Ring for PEM Dust Cap
Our Price: $2.57
Free Shipping
Small O-Ring for PEM GN Hub Dust Cap.

1.629 inch OD x 1.489 inc ID x .70 inch thick


 		THIN HUB O-RING FOR PEM GN HUBS

4.129 inch OD x .3.989 inch ID x .70 inch thick
Not the usual o-ring for PEM GN Hubs. 		Thicker O-Ring for Grand National Hubs

4.125 inch OD x .3.859 inch ID x 1.39 inch thick
Not the usual o-ring for PEM GN Hubs.
Lock Washer for GN 2.5" Snout Double Lip Seal for GN Hub GN Snout Seal for stepped GN axle
Lock Washer for 2.5" GN Snout
 		Hub Seal for 2.5" Grand National Hub

Double Lip Seal

 		snaps in end of 2.5" Grand National snout to seal
a stepped GN axle
ID 1.375 INCH
OD 1.878 inch
Blue
These snout seals do not fit PEM axles,
For PEM axles you need to use the green seal GNSSW5
Tapered Screws for PEM GN Drive Flange GN Snout Seal for wide 5 axle GDAXPLUG
GDAXPLUG
Our Price: $11.54
Free Shipping
Bolt Flat Head Cap Screw Drive Flange
5/16 diameter 18 tpi 1/2 long Grade 8 steel UnderCut for use with PEM Drive flanges
2 piece Kit
snaps in end of 2.5" Grand National snout
to seal a wide 5 axle
Green
ID 1.25 inch
OD 1.874 inch
This seals fits all PEM wide 5 axles (solid & Gun drilled).
Will not fit small Torque Axles

 		plug for dun drilled axle
so you can set axle spacing
Race for Grand National Bearing Kit - Grand National Dust Cover Black Right Hand Snout Nut for GN 2.5" Snout
Race only for GN 2.5" ID Hub Bearing
BL610510 		PEM GN Duct Cover Kit
Grand National Dust Cover Black]
fit PEM LW GN Hubs (will not fit Winters hubs)
aluminum dust cap with o-ring & 3 screws 		Grand National Snout Nut, RH thread.

Fits GN 2.5" Snout
Grand National Dust Cover kit - Thick Grand National Bearing Grand National Locking Right Hand Nut Kit
Grand National Bearing
Our Price: $17.06
Free Shipping
PEM GN Duct Cover Kit, New Thicker dust cover

Should fit most GN 2.5 inch bearing LW hubs
aluminum dust cap with o-ring & 3 screws 		GN 2.5" ID Hub Bearing
BL610549

This bearing fits 2.5" Grand National Snout

 		Locking Right Hand Thread Nut Kit
for 2.5" Grand National Hub
Press in 5/8" wheel studs 3 3/4" long 5 pack Screw in 5/8" wheel studs 3 3/4" long 5 pack for PEM 4.75 BC hubs GN Hub Nut Socket for 2.5 inch GN Hub Nut
Wheel Stud Press In 5 piece Kit Long 5/8" Coarse

fits PEM GN floater hubs 3 3/4" long


PEM 4.75 GN Hub Screw In 5 piece Kit Long 5/8" Coarse.


These only fit PEM and Winters 2.5" GN Hubs with 5 x 4.75" bolt pattern
5/8" coarse thread for lug nuts and fine thread where it screws into the hub
Lug Nut thread 3.75" long


 		Grand National Hub Nut Socket for 2.5 inch bearing hubs
fits N-12 GN Nut

Ford 9" Inner Axle Tube Seal Ford 9" Metric Housing Bushings, pair Grand National Bearing and Accessory Kit
UPDATED FOR 2025 WITH MORE PLIABLE RUBBER SEAL
Ford 9" Inner Axle Tube SeaL
Fits 3.0" OD x 3/16" wall rear end tubes
1.15" ID of rubber seal


Ford 9" Metric Housing Bushings
1978-1987 GM Metric Mid Size Cars
Polyurethane - Pair
Length of outer steel shell 2.10"
Bolt Hole Size .500"
 		GN Hub Bearing Kit 2 of ZGN 601549 2.5" hub bearings Double lip seal,
Lock washer, dust cap o-ring and thin hub O-ring
Rear GN Hub Bearing Spacer Grand National 2.5" RH Thread Snout Rotor .810 x 11.750 8 on 7" Bolt circle for Grand National Hub
GN Hub Bearing Spacer for 2.5" ID bearing GN Rear Hubs
Reduce drag by not ovetightening wheel bearings.
Goes between hub bearings. You must adjust to set drag on bearings.
Best used with REM Polished Bearings and Daylube wheel bearing grease
Sold each
For 2.5" Bearing and GN Hub. Right Hand Thread.
CNC Machined from Alloy Steel and has step for axle snout seal 		Rotor .810 x 11.750 8 on 7" Bolt circle for Grand National Hub
Metric Lower Trailing Arm Mounts Rear- PAIR Grand National Bearing and Race Kit - 1 wheel Wide 5 Steel Snout
Wide 5 Steel Snout
Our Price: $62.85
Free Shipping
pair of weld on Metric Lower
Radius Mounts for 3" OD Tube
4 OPTIONS ...

2.75" from bottom of tube to center of hole
2.5" from bottom of tube for IMCA Hobby Stock
2.25" from bottom of tube for USRA Souther Limited Modified
 		two of GN 2.5" ID Hub Bearings - BL610549
two of GN Hub Races for above bearings - BL610510

These fit 2.5" Grand National Snouts.
Wide 5 steel snout
CNC Machined from Alloy Steel
Howe Vogel 2 inch bearing Steel Snout Ford 9" Metric Upper Trailing Arm Mounts Rear w/out bushing 16 Bolt Snout Adapter Steel weld-in for bolt on snouts
2 inch Howe Vogel Snout
CNC Machined from Alloy Steel 		Weld On GM Metric Top Triailing Arm Mounts - set

  • Welds on 9 inch Ford housings with centered pinion
  • for stock General Motors 1978-88 Metric (mid-size) rear suspension trailing arms
  • Bushings Not Included
  • Raw Mild Steel, Not painted
 		16 bolt end for the 8 bolt spindle snouts
allows for more adjusment for toe and camber than an 8 bolt housing end
welds in 3 inch OD x .188" wall rear end tubing
5/16 - 24 thread