|
|
|
|
|
|
|
|
|
|
|
|
|
Dana 30 / 44 / 60 Front Axle Seal Installer
Includes, Install puck and stud, nut, and thrust block
|
Dana 60 1350 Black Forged Yoke
- 29 spline
- 1350 u-joint size
- 3.625" snap ring span
- 1.188" cap diameter
- Outside snap ring design
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dana 44 Full Spool 30 spline 3.92 and higher ratios - New Alloy Heat Treated Steel
- Application for 3.92 up to 5.89 numerically higher ratios
- Locks up Dana 44 Front and Rear Ends
|
- Easily set carrier bearing preloads safely
- Can be used for Dana 30 thru Dana 80 Housings
- Does not work with Corvette Housings
- Does not work with Dana 35 Housings with dowels under the cover
- Can be used for GM10 and 12 Bolt Housings by making custom pins from a 7/8 Fine Thread Bolt
- Dowel Pins measure 13 11/16 inches from center of pin to center of pin when fully adjusted out, and then down to 11 3/8 inches at its narrowest point.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Forged Ford 1410-31 Spl Diff Yoke 10.25 Sterling- For Early Models (92 and older) with 1.265' Spline Length
|
|
Dana 60 Drive Flange Kit with Slugs
for Chevy and Ford 35 spline outer axle
flanges for both sides
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Stock replacement JK rear 1310 greaseable D/S
|
Stock replacement JK/ JKU 07-17 front 1310 greaseable
|
Stock Front JK driveshaft replacement kit includes: transfer case yoke and greaseble 1310 u-joints
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Stock Rear JK drive shaft replacement Kit includes: transfer case yoke,
differential yokes, hardware and greaseable 1310 u-joints
|
Front JK driveshaft replacement kit includes: transfer case and differential yokes, with solid 1310 u joints and full spline stub shaft.
|
Rear JK drive shaft replacement kit includes: transfer case and differential yokes, solid 1310 u-joints and full spline stub shaft.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Front JK driveshaft only, solid 1350 u-joints, full spline stub shaft
|
Rear Jk drive shaft only includes: solid 1350 u-joints, full spline stub shaft
|
9 Inch Ford Center Section with "Brute" 3.250" Case and 35 Spline Full Spool
- Cast Daytona Pinion Support
- Forged 1350 Pinion Yoke
- Standard (Competiton Cut Gear) or Premium Street Gear (Upgrade)
- Standard Ratios Available: 4.57, 4.71, 4.86, 5.00, 5.14, 5.29, 5.43, 5.67, 5.83, 6.20
- Premium Street Gear Ratios: 3.25, 3.50, 3.70, 4.11, 4.86, 5.29
***Standard Gear is meant for offroad applications only (More gear noise than premium gear)***
***Premium Street Gear is meant for the Street and Trail***
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Front JK driveshaft replacement kit includes: transfer case flange, diff yoke, solid 1350 u joints and full spline stub shaft
|
Complete Rear JK driveshaft includes: transfer case flange, and diff yoke,
solid 1350 u-joints, hardware and full spline stub shaft
|
9 Inch Ford Center Section with "Brute" 3.250" Case and 35 Spline Detroit Locker
- Cast Daytona Pinion Support
- Forged 1350 Pinion Yoke
- Standard (Competiton Cut Gear) or Premium Street Gear (Upgrade)
- Standard Ratios Available: 4.57, 4.71, 4.86, 5.00, 5.14, 5.29, 5.43, 5.67, 5.83, 6.20
- Premium Street Gear Ratios: 3.25, 3.50, 4.86, 5.29
***Standard Gear is meant for offroad applications only (More gear noise than premium gear)***
***Premium Street Gear is meant for the Street and Trail***
SHIPS WITHIN ONE WEEK
|
|
|
